====== Ubuntu - iptables - Create a VPN Kill Switch ====== Use iptables to block all Internet connections in the event your VPN is disconnected. It's a mechanism that stops your Internet connection when you're disconnected from the VPN. It protects you from inadvertently leaking sensitive information onto the Internet when the VPN connection drops. Some VPN services provide clients with a built-in killswitch, but none are as reliable as using iptables. Since iptables is independent of your VPN service, and it's integrated into the kernel itself, it won't fail when your VPN does. Iptables is also a well-proven security technology that can and will keep your computer safe. ---- ===== Sysctl ===== Before you start creating iptables rules, you should make some alterations to the sysctl configuration. In some distributions, it's located at /etc/sysctl.d/99-sysctl.conf. Others have it at /etc/sysctl.conf. Open up that file, and locate the following line and change it to match the example here. net.ipv4.ip_forward=1 Then, add the following lines to the bottom of the file. Be sure to change the interfaces to match the ones on your machine. net.ipv6.conf.all.disable_ipv6 = 1 net.ipv6.conf.default.disable_ipv6 = 1 net.ipv6.conf.lo.disable_ipv6 = 1 net.ipv6.conf.eth0.disable_ipv6 = 1 Save and exit. Then run: # sysctl -p ---- ===== Set Up The Firewall Document ===== Create a file for your firewall rules. *filter COMMIT ---- ===== Base Rules ===== Before you configure iptables to allow any traffic you need to switch its default to disallow all traffic. Add these three rules to drop all traffic by default. -P INPUT DROP -P FORWARD DROP -P OUTPUT DROP ---- ===== Input ===== It's most secure to only allow inbound traffic from established or related connections. Set that up next. -A INPUT -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT ---- ===== Loopback and Ping ===== Next, allow the loopback interface and ping. -A OUTPUT -o lo -j ACCEPT -A OUTPUT -o tun0 -p icmp -j ACCEPT This assumes that your VPN connection is on **tun0**. Check that with **ip a**, if you're not sure. ---- ===== LAN ===== It doesn't make much sense to shut down or block your LAN traffic, especially on a home network, so allow that too. -A OUTPUT -d 192.168.1.0/24 -j ACCEPT ---- ===== DNS ===== You need to know the IP address of your VPN's DNS server(s). If your VPN has access or your resolv.conf, you'll probably find them in there. -A OUTPUT -d 10.45.16.1 -j ACCEPT ---- ===== Allow The VPN ===== You need to allow the VPN itself. There are two parts to this. You need to allow both the service port and the interface. -A OUTPUT -p udp -m udp --dport 1194 -j ACCEPT -A OUTPUT -o tun0 -j ACCEPT Again, check the port and interface that your VPN connection is using. You could stop here. This will work just fine for a killswitch. However, if you want iptables to function as a regular firewall and block connections on unwanted ports too, you can do that too. From here, you would delete the last line that accepts all traffic on tun0, and replace it with specific allowances for the ports that you want to allow. -A OUTPUT -o tun0 -p tcp --dport 443 -j ACCEPT -A OUTPUT -o tun0 -p tcp --dport 80 -j ACCEPT -A OUTPUT -o tun0 -p tcp --dport 993 -j ACCEPT -A OUTPUT -o tun0 -p tcp --dport 465 -j ACCEPT You get the general idea. It's longer and more tedious, but it gives you more control over what traffic gets through. ---- ===== IPv6 ===== IPv6 is really bad for VPNs right now. Most don't adequately support it, and your information can leak out over that connection. It's best to shut it down altogether. Create another file for IPv6 and block everything. -P INPUT DROP -P FORWARD DROP -P OUTPUT DROP ---- ===== Commit ===== You need to import your files into iptables in order for them to take effect. First, clear out any old rules. iptables -F && iptables -X Import the new ones from your files. iptables-restore < /tmp/ipv4 ip6tables-restore < /tmp/ipv6 ---- ===== Make It Permanent ===== iptables doesn't save its state after a reboot by default. You need to set that up yourself. ---- ===== Debian/Ubuntu ===== Debian-based systems have a program called, **iptables-persistent**. It's a service that handles backing up and loading your configurations. When you install it, iptables-persistent will ask you if you want to save your existing configuration. Say yes. apt install iptables-persistent Since Debian systems run services on startup by default, you don't need to do anything else. ---- ===== Other Systemd ===== Other systems have a couple of different ways to handle this. The first is to edit /etc/sysconfig/iptables-config. There will be one of two lines there. Edit the one that you have to look like the following. IPTABLES_SAVE_ON_STOP="yes" OR IPTABLES_SAVE_ON_RESTART="yes" The other way is to use the save and restore functions of iptables. Create a directory where you want to save your rules. mkdir /etc/iptables/ iptables-save > /etc/iptables/iptables.rules ip6tables-save > /etc/iptables/ip6tables.rules Then, create a script to load those rule when your computer boots up. #! /bin/bash iptables-restore < /etc/iptables/iptables.rules; ip6tables-restore < /etc/iptables/ip6tables.rules; ---- ===== OpenRC ===== OpenRC systems like Gentoo have their own way of saving the configurations. rc-service iptables save rc-service ip6tables save rc-service iptables start rc-service ip6tables start rc-update add iptables default rc-update add ip6tables default ---- ===== Closing Thoughts ===== Using an iptables-based killswitch makes your VPN much more secure. Leaking data makes totally defeats the purpose of using a VPN, so stopping leaks should be a top priority. Do not trust the so-called killswitches baked into VPN clients. Most don't work. The only way to really ensure that your data isn't leaking is to do it yourself with iptables.