Differences

This shows you the differences between two versions of the page.

--- pfsense:troubleshooting [2020/04/03 10:48] – peter
+++ pfsense:troubleshooting [2021/02/19 09:59] (current) – peter
@@ Line 1: / Line 1: @@
 ====== PFSense - Troubleshooting ======
-===== PFSENSE BEHIND A ROUTER =====
+[[PFSense:Troubleshooting:Amazon app reports "Ooops, an error has occurred"|Amazon app reports "Ooops, an error has occurred"]]
-From: http://hakology.co.uk/2014/02/pfsense-behind-a-router/
+[[PFSense:Troubleshooting:Crash Report|Crash Report]]
-<code>
+[[PFSense:Troubleshooting:Disk usage increasing|Disk usage increasing]]
-Can pfsense ping router – NO WAN config error
-Can pfsense ping pfsense client – NO – LAN config error / Client firewall
-Can pfsense client ping pfsense – NO – LAN config error / Client firewall
-Can pfsense ping 8.8.8.8 – NO – ASDL/CABLE router config error
-Can pfsense client ping router – NO – NAT error
-Can pfsense client ping 8.8.8.8 – NO – NAT error / ADSL / CABLE config error
-Can pfsense client ping 8.8.8.8 – YES – All good
-Can pfsense client load a website – NO – DNS Error – Check everything above is OK
-Can pfsense client load a website – YES – Everything is working
-</code>
-----
+[[PFSense:Troubleshooting:Firewall Blocking an Internal Address|Firewall Blocking an Internal Address]]
-===== SSL_ERROR_RX_RECORD_TOO_LONG =====
+[[PFSense:Troubleshooting:mbuf full|mbuf full]]
-Getting the error **SSL_ERROR_RX_RECORD_TOO_LONG** when attempting to access multiple different sites, sometimes goes away with refresh but sometimes persists.
+[[PFSense:Troubleshooting:PfSense is restoring the configuration|PfSense is restoring the configuration]]
-{{:pfsense:pfsense_ssl_error_rx_record_too_long.png?800|}}
+[[PFSense:Troubleshooting:SSL_ERROR_RX_RECORD_TOO_LONG|SSL_ERROR_RX_RECORD_TOO_LONG]]
-Usually when using Squid option of **Splice All** for SSL/MITM Mode.
+[[PFSense:Troubleshooting:Tuning and Troubleshooting Network Cards|Tuning and Troubleshooting Network Cards]]
-Can't connect to 192.168.1.1:443 (certificate verify failed)
+[[PFSense:Troubleshooting:OpenVPN Client Common Name shows as UNDEF|OpenVPN Client Common Name shows as UNDEF]]
-<code>
+[[PFSense:Troubleshooting:Out of disk space on /var/run|Out of disk space on /var/run]]
-SSL connect attempt failed error:1416F086:SSL routines:tls_process_server_certificate:certificate verify failed at /usr/share/perl5/LWP/Protocol/http.pm line 50.
-</code>
-Check:
-<code bash>
-openssl s_client -connect 192.168.1.1:443
-</code>
-returns:
-<code bash>
-...
-Verify return code: 21 (unable to verify the first certificate)
-...
-</code>
+----
+===== PFSENSE BEHIND A ROUTER =====
-==== Solution ====
+From: http://hakology.co.uk/2014/02/pfsense-behind-a-router/
+<code>
+Can pfsense ping router – NO - WAN config error.
+Can pfsense ping pfsense client – NO – LAN config error / Client firewall.
+Can pfsense client ping pfsense – NO – LAN config error / Client firewall.
+Can pfsense ping 8.8.8.8 – NO – ASDL/CABLE router config error.
+Can pfsense client ping router – NO – NAT error.
+Can pfsense client ping 8.8.8.8 – NO – NAT error / ADSL / CABLE config error.
+Can pfsense client ping 8.8.8.8 – YES – All good.
+Can pfsense client load a website – NO – DNS Error – Check everything above is OK.
+Can pfsense client load a website – YES – Everything is working.
+</code>
-  * **Servicess -> SquidGuard Proxy Filter -> Common ACL -> ALL to allow**
+If you are having issue make sure you disable any firewalls you have running on the pfsense client boxes … once you have your network configured you can enable them later.
-  * May need to refresh the browser cache:
+----
-    * CTRL F5
-    * CTRL+SHIFT+r
-    * SHIFT+reload button
-  * Might need to turn off support for the newest and most secure connection protocol, TLS 1.3.
-    * In Firefox
-      * Type **about:config** in the address bar and press Enter/Return.
-      * In the search box above the list, type **TLS**.
-      * Double-click the **security.tls.version.max** preference to display a dialog where you can edit the value from 4 to 3 (or in other words, from TLS 1.3 to TLS 1.2).
-      * Then click **OK**.
-----