Differences

This shows you the differences between two versions of the page.

--- pfsense:install_pfsense:interface_creation_and_configuration [2020/11/30 22:39] – peter
+++ pfsense:install_pfsense:interface_creation_and_configuration [2020/11/30 22:42] (current) – removed peter
@@ Line 1: / Line 1: @@
-====== PFSense - Install pfSense - Interface Creation and Configuration ======
-===== Create Interfaces =====
-Create an interface per VLAN.
-Navigate to **Interfaces -> Assignments**.
-  * Select **VLAN50 on em1** from the available network ports.
-  * Click **Add**.
-  * Select **VLAN70 on em1** from the available network ports.
-  * Click **Add**.
-  * Select **VLAN99 on em1** from the available network ports.
-  * Click **Add**.
-<WRAP info>
-**NOTE:**  This should show the following Interfaces:
-  * OPT1
-  * OPT2
-  * OPT3
-</WRAP>
-----
-===== Configure interface IP addresses =====
-Navigate to **Interfaces -> Assignments**.
-  * Click on the label next to **VLAN50**, its likely to be **OPT1**.
-Configure this interface as follows:
-In **General Configuration**:
-  * Enable:  **Checked**.
-  * Description:  **CLEAR**.
-  * IPv4 Configuration Type:  **Static IPv4**.
-  * IPv6 Configuration Type:  **None**.
-  * MAC Address:  **<default>**.
-  * MTU:  **None**.
-  * MSS:  **None**.
-  * Speed and Duplex:  **Default (no preferences, typically autoselect)**.
-In **Static IPv4 configuration**:
-  * IPv4 Address:  **192.168.50.1/24**.
-  * IPv4 Upstream gateway:  **None**.
-In **Reserved Networks**:
-  * Block private networks and loopback addresses:  **Not Checked**.
-  * Block bogon networks:  **Not Checked**.
-Click **Save** and Apply changes.
-{{:pfsense:install_pfsense:pfsense_-_interfaces_-_clear.png?800|}}
-----
-Navigate to **Interfaces -> Assignments**.
-  * Click on the label next to **VLAN70**, its likely to be **OPT2**.
-Configure this interface as follows:
-In **General Configuration**:
-  * Enable:  **Checked**.
-  * Description:  **IOT**.
-  * IPv4 Configuration Type:  **Static IPv4**.
-  * IPv6 Configuration Type:  **None**.
-  * MAC Address:  **<default>**.
-  * MTU:  **None**.
-  * MSS:  **None**.
-  * Speed and Duplex:  **Default (no preferences, typically autoselect)**.
-In **Static IPv4 configuration**:
-  * IPv4 Address:  **192.168.70.1/24**.
-  * IPv4 Upstream gateway:  **None**.
-In **Reserved Networks**:
-  * Block private networks and loopback addresses:  **Not Checked**.
-  * Block bogon networks:  **Not Checked**.
-Click **Save** and Apply changes.
-{{:pfsense:install_pfsense:pfsense_-_interfaces_-_iot.png?800|}}
-----
-Navigate to **Interfaces -> Assignments**.
-  * Click on the label next to **VLAN99**, its likely to be **OPT3**.
-Configure this interface as follows:
-In **General Configuration**:
-  * Enable:  **Checked**.
-  * Description:  **GUEST**.
-  * IPv4 Configuration Type:  **Static IPv4**.
-  * IPv6 Configuration Type:  **None**.
-  * MAC Address:  **<default>**.
-  * MTU:  **None**.
-  * MSS:  **None**.
-  * Speed and Duplex:  **Default (no preferences, typically autoselect)**.
-In **Static IPv4 configuration**:
-  * IPv4 Address:  **192.168.99.1/24**.  Alternatively use a completely different IP range for Guests such as **172.16.0.1/24**.
-  * IPv4 Upstream gateway:  **None**.
-In **Reserved Networks**:
-  * Block private networks and loopback addresses:  **Not Checked**.
-  * Block bogon networks:  **Not Checked**.
-Click **Save** and Apply changes.
-{{:pfsense:install_pfsense:pfsense_-_interfaces_-_guest.png?800|}}
-----